T-max manager keep beeping

gofis · 06-16-2005, 10:06 AM

Need some help here please. My beds has gone crazy. It just starting beeping yesterday, when I reset the T-max manager(pro), none of the beds show up. I figured out that two of the beds are the cause of this. If one or both of the beds are in the chain of the T-max manager, the T-max does not recognize any of the bed. I bypass those two bed, the T-max recognize the beds. Those two beds work fine if the terminators are plug into the units. All the beds ard ETS beds

_________________
[ This Message was edited by: gofis on 2005-06-16 10:27 ]

Kevin Barrett · 06-22-2005, 09:04 AM

Sorry for the late response. I just saw this post.

This means that there is something wrong with either the timers in the beds or setting on the timers in these two beds. Check the addresses first (on the tanning bed in the two rooms in question). Make sure they are set to the correct room numbers. Duplicate addresses can cause this problem.

If that does not fix this, then there is a problem most likely with the communications chips on those two beds.

Kevin Barrett
ADI Tech Support

gofis · 06-22-2005, 09:10 PM

Thanks for the response. It was the comm chips. Replaced the chips, the beds are working with the T-max manager now. There is another problem, The computer is not seeing the T-max manager. Could it be the comm chip in the T-max manager that is bad?

thanx

Kevin Barrett · 06-23-2005, 08:15 AM

There is an RS232 chip in the T-Max Manager that could be the problem. It could also be the computer's Serial port.

Kevin Barrett
ADI Tech Support

_________________
[ This Message was edited by: Kevin Barrett on 2005-06-23 08:15 ]

gofis · 06-23-2005, 09:00 AM

I am working on the serial port, but the RS232 chip in the T-max manager, is it user replacable? and where can I get my hands on one?

Thanx

Kevin Barrett · 06-24-2005, 09:20 AM

Yes the chip is user replacable (it's in a socket). Simply pry the original one out and replace it with a new one. You can get one from any of my distributors.

Kevin Barrett
ADI Tech Support

gofis · 06-26-2005, 10:29 AM

I think it's the RS232 chip. Could you PM me the names of some of your disty( Kevin)

thanx

Kevin Barrett · 06-27-2005, 08:00 AM

Done.

Kevin Barrett
ADI Tech Support

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Hiring a manager	susanlatte	Salon Management	18	08-15-2004 06:07 PM
T-Max manager Pro Problems	Cliptfc	Open Forum	2	08-04-2004 06:14 PM
Will a T-Max 1a work with a Manager Pro?	tan-tone	Technology Forum	2	03-02-2002 07:26 PM
Manager won\'t show clean bed.	Ginger	Technology Forum	9	02-14-2002 12:07 PM
manager pro, or manager	Sonshinetans	Technology Forum	4	07-31-2001 07:39 AM

06-16-2005, 10:06 AM	#1 (permalink)
gofis Join Date: Aug 26 2004 Location: US Posts: 34 Rep Power: 0	Need some help here please. My beds has gone crazy. It just starting beeping yesterday, when I reset the T-max manager(pro), none of the beds show up. I figured out that two of the beds are the cause of this. If one or both of the beds are in the chain of the T-max manager, the T-max does not recognize any of the bed. I bypass those two bed, the T-max recognize the beds. Those two beds work fine if the terminators are plug into the units. All the beds ard ETS beds _________________ [ This Message was edited by: gofis on 2005-06-16 10:27 ]

06-22-2005, 09:04 AM	#2 (permalink)
Kevin Barrett Join Date: Jan 26 2000 Location: Branson West, MO Age: 42 Posts: 210 Rep Power: 9	Sorry for the late response. I just saw this post. This means that there is something wrong with either the timers in the beds or setting on the timers in these two beds. Check the addresses first (on the tanning bed in the two rooms in question). Make sure they are set to the correct room numbers. Duplicate addresses can cause this problem. If that does not fix this, then there is a problem most likely with the communications chips on those two beds. Kevin Barrett ADI Tech Support

06-22-2005, 09:10 PM	#3 (permalink)
gofis Join Date: Aug 26 2004 Location: US Posts: 34 Rep Power: 0	Thanks for the response. It was the comm chips. Replaced the chips, the beds are working with the T-max manager now. There is another problem, The computer is not seeing the T-max manager. Could it be the comm chip in the T-max manager that is bad? thanx

06-23-2005, 08:15 AM	#4 (permalink)
Kevin Barrett Join Date: Jan 26 2000 Location: Branson West, MO Age: 42 Posts: 210 Rep Power: 9	There is an RS232 chip in the T-Max Manager that could be the problem. It could also be the computer's Serial port. Kevin Barrett ADI Tech Support _________________ [ This Message was edited by: Kevin Barrett on 2005-06-23 08:15 ]

06-23-2005, 09:00 AM	#5 (permalink)
gofis Join Date: Aug 26 2004 Location: US Posts: 34 Rep Power: 0	I am working on the serial port, but the RS232 chip in the T-max manager, is it user replacable? and where can I get my hands on one? Thanx

06-24-2005, 09:20 AM	#6 (permalink)
Kevin Barrett Join Date: Jan 26 2000 Location: Branson West, MO Age: 42 Posts: 210 Rep Power: 9	Yes the chip is user replacable (it's in a socket). Simply pry the original one out and replace it with a new one. You can get one from any of my distributors. Kevin Barrett ADI Tech Support

06-26-2005, 10:29 AM	#7 (permalink)
gofis Join Date: Aug 26 2004 Location: US Posts: 34 Rep Power: 0	I think it's the RS232 chip. Could you PM me the names of some of your disty( Kevin) thanx

06-27-2005, 08:00 AM	#8 (permalink)
Kevin Barrett Join Date: Jan 26 2000 Location: Branson West, MO Age: 42 Posts: 210 Rep Power: 9	Done. Kevin Barrett ADI Tech Support

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)