Go Back   tanTALK - Tanning Salon Business Owners Community > TanTalk Central > Sun Doctors

Sun Doctors Ask here if you have any technical questions related to your tanning equipment. Please fee free to post your repair need so our Sun Doctors may help you.

Reply
 
LinkBack Thread Tools
Old 09-16-2012, 11:24 AM   #1 (permalink)
 
Join Date: Aug 7 2012
Location: Reykjavík
Posts: 5
Rep Power: 0 Baldvin is on a distinguished road
Red face error code 102 ergoline

I am having a problem with Ergoline 500
Is there some one than knows how to fix e102 (problem in safety chain) ?
Baldvin is offline   Reply With Quote
Old 09-26-2012, 03:33 AM   #2 (permalink)
 
Join Date: Sep 26 2012
Location: Poland
Posts: 18
Rep Power: 0 sunlife is on a distinguished road
Re: error code 102 ergoline

From system massages:
E 102/92 System message: wiring power error in the safety chain
• This system message is a logical error, i.e. when power is connected to some point of the safety chain but this should not
be the case, e.g. because of an open safety switch. (wiring or connection error)
-> control plugs and sockets (correct allocation)

Next..
On mainboard, check all signals ways in socket X1 input ( step 1 visually, 2 - check 230V, 3 check resistance, 4 - replace all )
sunlife is offline   Reply With Quote
Old 10-07-2012, 11:01 AM   #3 (permalink)
 
Join Date: Aug 7 2012
Location: Reykjavík
Posts: 5
Rep Power: 0 Baldvin is on a distinguished road
Re: error code 102 ergoline

Thank you for this ! I think this might be the problem.
Is possible ti repair the main PCB ?
Do I replace only nr. 4 ?
Baldvin is offline   Reply With Quote
Old 10-08-2012, 08:20 AM   #4 (permalink)
 
Join Date: Sep 26 2012
Location: Poland
Posts: 18
Rep Power: 0 sunlife is on a distinguished road
Re: error code 102 ergoline

Quote:
Originally Posted by Baldvin View Post
Thank you for this ! I think this might be the problem.
Is possible ti repair the main PCB ?
Yes.

Quote:
Originally Posted by Baldvin View Post
Do I replace only nr. 4 ?
I do this in all used PCB. If they was OK , this will increase lifetime of capacitors and PCB.

Say more about problem, this is new installation? Do You trust to connection outside PCB? Have You other PCB to replace and confirm PCB problem ( PCB from other Ergoline with E1 PCB - You must replace Eprom and TimeKeeper )...
sunlife is offline   Reply With Quote
Old 10-08-2012, 07:25 PM   #5 (permalink)
 
Join Date: Aug 7 2012
Location: Reykjavík
Posts: 5
Rep Power: 0 Baldvin is on a distinguished road
Re: error code 102 ergoline

Hello Sunlife.
Thank you so much to take the time to answer me.
This is the problem I have another PCB to test in this sunbed.
If I change the eprom, do I need to program it ?
What is the timeKeeper is that one also in the PCB ?
There is a problem getting those parts in Iceland, Do you know where I can get the parts ?

Best regards
Baldvin
Baldvin is offline   Reply With Quote
Old 10-09-2012, 02:07 AM   #6 (permalink)
 
Join Date: Sep 26 2012
Location: Poland
Posts: 18
Rep Power: 0 sunlife is on a distinguished road
Re: error code 102 ergoline

Quote:
Originally Posted by Baldvin View Post
This is the problem I have another PCB to test in this sunbed.
?
If You have not another PCB, IMO you don't need to change eprom and timekeeper ( this step is only for replaced PCB with other Eprom - eprom store program specific for unit version - timekeeper store settings and realtime control ). Sometime eprom is defective, look on label - if there is overheated paper in center -> eprom must be replaced.
Timekeeper is the big black chip on right site near eprom ( old version have printed "Timekeeper", new one M48T02 ).

This error code is very specific, problem can be with PCB and outside PCB ( broken or mistaken connection) - changing PCB is fastest elimination test.
sunlife is offline   Reply With Quote
Old 10-09-2012, 04:08 PM   #7 (permalink)
 
Join Date: Aug 7 2012
Location: Reykjavík
Posts: 5
Rep Power: 0 Baldvin is on a distinguished road
Re: error code 102 ergoline

Hello.
The problem is inside the PCB.
I think the eprom is ok.
What parts do I change ?

Best regards
Baldvin
Baldvin is offline   Reply With Quote
Old 10-09-2012, 04:35 PM   #8 (permalink)
 
Join Date: Sep 26 2012
Location: Poland
Posts: 18
Rep Power: 0 sunlife is on a distinguished road
Re: error code 102 ergoline

1. all capacitors in square 4
2. overheated resistors in the center of square 3

You can observe LEDs in square 1 - but this needs power on and more understanding ( generally , lighting leds must have the same level of brightness and working one must shine / Working one in right time -> led of wind switch and leds of studio control after session start - other alway if no problem with secure loop and switches / ).

Change this capacitors first , please - don't wait so long ... ;)
sunlife is offline   Reply With Quote
Old 10-09-2012, 04:39 PM   #9 (permalink)
 
Join Date: Aug 7 2012
Location: Reykjavík
Posts: 5
Rep Power: 0 Baldvin is on a distinguished road
Re: error code 102 ergoline

Thank you so much !!!
I will do this tomorrow.

Best regards
Baldvin
Baldvin is offline   Reply With Quote
Old 06-11-2014, 12:46 PM   #10 (permalink)
 
Join Date: May 25 2011
Location: Kiev, Ukraina
Posts: 1
Rep Power: 0 Taras is on a distinguished road
Re: error code 102 ergoline

ThankYou!
Your information is help me!

Best regards
Taras.
Taras is offline   Reply With Quote
Reply

Bookmarks

Tags
e102



Currently Active Users Viewing This Thread: 2 (0 members and 2 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Similar Threads
Thread Thread Starter Forum Replies Last Post
Solaris Error Code csisatellites General Tanning Industry Discussions 5 05-02-2012 04:01 PM
Saturn error code? jam Sun Doctors 0 03-22-2011 08:00 AM
ergo 800 error code 62 t-n-t Sun Doctors 3 03-30-2010 05:38 AM
Sundash error code L31-Help jennb73 Sun Doctors 2 03-27-2009 10:51 PM
T-max 3A error code? skycam Technology Forum 3 05-09-2001 07:52 AM


All times are GMT -5. The time now is 01:33 PM.


Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
LinkBacks Enabled by vBSEO 3.1.0
Copyright 2009 - tanTALK.com

click here for advertising info!